Oil Seal in Motor:

Just like pressure. The temperature capability of the oil seal shouldn’t be lesser than the temperature of the application. This is because any significant increase or even decrease in the temperature will affect the functionality of the oil seal. PTFE seals have the highest temperature capability, making them useful for applications that demand harsh weather and elements.

Under the action of the skeleton oil seal, the rigidity of the oil film just makes the oil film and the air contact end form a crescent surface, which prevents the leakage of the working medium and realizes the sealing of the rotating shaft. The sealing ability of the oil seal depends on the thickness of the oil film on the sealing surface. If the thickness is too large, the oil seal will leak; if the thickness is too small, dry friction may occur, causing the oil seal and shaft to wear; if there is no oil film between the sealing lip and the shaft, it is easy to cause heat and wear. . Therefore, when installing, it is necessary to apply some oil on the sealing ring, and at the same time ensure that the skeleton oil seal is perpendicular to the axis line. If it is not perpendicular, the sealing lip of the oil seal will drain the lubricating oil from the shaft, which will also lead to excessive sealing of the lip. wear. During operation, the lubricant in the casing seeps out a little, so that it is ideal to form an oil film on the sealing surface.

Oil seals, also referred to as shaft seals, are widely used to prevent the leakage of medium (such as oils and grease) along a rotating shaft. This leak prevention is primarily achieved by the sealing element which can be made from a wide range of materials that are chosen according to each application. They are commonly used in gearboxes, hydraulic cylinders, and related components.

Oil seal WG1087811 is used by several automotive manufacturers, such as Opel, Fiat and Suzuki, and serves as a good example for an oil seal where oil leakage can occur if fitted incorrectly.

If the seal is being fitted to original equipment you may have some influence over the shaft and housing bore finish, but if you are replacing a worn seal you still need to take into account the condition of these 2 essential parts. Check for sharp edges and burrs – particularly on the shaft and housing chamfers or you could ruin the seal before you start up. If the shaft is too worn consider using an M Barnwell Services Shaft Repair Kit.

A standard oil seal consists of an outer circular metal disk with an inner flexible rubber which is affixed to the metal during vulcanization. The bonded seal has no loose parts to allow leakage of oil or ingress of any contaminants. This kind of seal is more accurate, and can easily be fitted into a smaller space. An example is shown in Figure 2.9.

This is one of the frequent reasons for oil seal failure, and this is majorly because of the volatility of any of the elastomer’s constituents. These causative constituents may be part of the elastomer formulation, or gases that got entrapped in the elastomer during the molding process. The deceiving fact about this failure is that sometimes the oil seal won’t show any visual sign of out-gassing, however, sometimes when the out-gassing is extreme, they shrink.

Classical oil seals consist of a metal housing that carries the dynamic sealing lip and provides the static sealing function. These are usually manufactured of elastomer material, such as ACM, Silicone or FPM. Further, since they are in contact with the surface of the rotating shaft, the lip is pressed onto the shaft surface by means of a spring ring.

Remove all traces of the old gasket from the pump and engine, using a paint scraper if necessary.

When choosing a type of oil seal, it is important to consider factors such as environment, shaft speed and pressure of your machine, temperature, and the type of materials the seal will interact with during use. These considerations will ensure that you choose a compatible oil seal for your particular machinery and help you select the right color, size, and lip material or sealing element. 

B

Polyacrylate Oil Seals - Mostly selected for automotive and transmission uses, polyacrylate seals are able to withstand fuel, oil, ozone, sunlight and weather when used. With cars exposed to all these different fluids and elements, they are the perfect choice. However, they should not be used in low temperatures, as their flexibility weakens when cold.

These oil seals are created from a low-temperature tolerant compound.  Benefits include: